C.Itoh EZ-1305 User Manual

User’s Manual EZ-1105 / EZ-1305 P/N. 920-013611-01Rev. A, 08.2009

4632151. Thermal Print Head 2. Label Guide3. Platen Roller4. Print Line Adjustment Gear5. Ribbon Core Holder (supply)6. Label Sensor1. Fan-Fold Label

2. Printer Installation This printer model has the following print modes:ThermalTransfer (TT)When printing, ribbon must be installed to transfer the p

5. Feed the ribbon from the Ribbon Supply Shaft. 6. Wrap the ribbon around thePrinting Mechanism and stick the ribbon onto the rewind ribbon roll.7. R

2-2. Label Installation 1. Open the top cover by pressingthe Cover Open Buttons on both sides.2. Place the label roll onto the Label Roll Core. 3. Pre

2-3. Label Roll Core Installation Instruction (A) 1” roll core installation (B) 1.5” roll core installation EZ-1105 / EZ-1305 User’s Manual13

2-4. PC Connection 1. Please make sure the printer is powered off. 2. Plug the power cable into the power socket on the wall, and then connect the oth

2-5. Driver Installation 1. Insert the product CD to your computer’s CD Drive and find the "Windows Drives" folder.2. Select the icon of dri

6. Select connection port.7. Enter the printer name andset printer sharing option.8. A description page of printersettings will be displayed after all

3. Printer Setting 3-1. FEED KeyAfter pressing the FEED key, printer will feed the media (according to media type) to the specified stop position. Whe

3-4. Self-Test page The Self-Test page helps user to figure out whether the printer is operating normally. Below are some general descriptions about t

FCC COMPLIANCE STATEMENTFOR AMERICAN USERSThis equipment has been tested and found to comply with the limits for a CLASS A digital device,pursuant to

3-5. Error Messages When an error happened during printing process, different LED light messages will be displayed.Users can diagnose the error situat

4. Accessory 4-1. RS-232 Module Installation 1 Module Connection Wire 2 RS-232 module3 Secure Screw4 RS-232 Back Panel μNoteνPlease make sure that ant

8. Use long-nose pliers to loosen andremove the hexagonal screws on both sides of RS-232 module.9. Align the RS-232 module to the RS-232port and plug

4-2. Ethernet Module Installation 1 Ethernet Cable 1.8M 2 Ethernet module3 Module Connection Wire 4 Ethernet Back Panel 5Secure Screw 6Hex Threaded St

7. Lift up the mainboard. Align the Hex Threaded Stand-off and Hex ThreadedStand-off Screw to each other andtighten as the figure showed.8. Align the

12. Align the Bottom Cover to the hooks andreassemble it. 13. Tighten bottom case screws to completethe installation. μNoteνAfter the Ethernet module

5. Maintenance and Adjustment 5-1. Thermal Print Head Cleaning Unclear printouts may be caused by dusty print head, ribbon stain or label liner glue.

5-3. Print Line Adjustment To get better printing balance andquality, use print head adjusting gearto adjust the contacting surfacebetween print head

5-4. TroubleshootingProblem Recommended SolutionPower on the printer, but the LED does not light up i Check the power connectorLED light turns red (po

Safety Instructions Please read the following instructions seriously.1. Keep the equipment away from humidity.2. Before you connect the equipment to t

Safety InstructionsBitte die Sicherheitshinweise sorgfältig lesen und für später aufheben.1. Die Geräte nicht der Feuchtigkeit aussetzen.2. Bevor Sie

1. BARCODE PRINTER... 51-1. Printer Accessories...

1. Barcode Printer 1-1. Printer Accessories After unpacking, please check the accessories that come with the package, and storeappropriately. Barcode

Code PagesCODEPAGE 437, 850, 851, 852, 855, 857, 860, 861, 862, 863, 865, 866, 869, 737WINDOWS 1250, 1251, 1252, 1253, 1254, 1255 Unicode (UTF8, UTF16

1-3. Communication InterfaceUSB Interface Connector Type : Type B PIN NO. 1 2 3 4FUNCTION VBUS D- D+ GNDSerial Interface (Optional) Serial DefaultSet

1-4. Printer Parts 2134561. Cover Open Button 2. Top Cover3. Label Roll Core4. Ribbon Rewind Wheel5. Print Mechanism6. Ribbon Core Holder (rewind)2145