C.Itoh EZ-1100 plus User Manual

User’s Manual EZ-1000Plus P/N. 920-012411-03 Rev. A, 08.2009

1-4. Printer Parts 21345678 1. Cover Open Button 2. Top Cover 3. Label Roll Core 4. Ribbon Rewind Wheel 5. Print Mechanism 6. Ribbon Rewind Shaft

45132 1. Ribbon Supply Shaft 2. Label Guide 3. Platen Roller 4. Print Line Adjustment Gear 5. Label Sensor 1254673 1. Fan-Fold Label Insert 2. P

2. Printer Installation This printer model has the following print modes: Thermal Transfer (TT) When printing, ribbon must be installed to transfer th

4. Feed the ribbon from the Ribbon Supply Shaft under the Print Head. 5. Wrap the ribbon around the Ribbon Shaft and stick the ribbon onto the Empt

2-2. Label Installation 1. Open the top cover by pressing the Cover Open Buttons on both sides. 2. Place the label roll onto the Label Roll Core.

2-3. Label Roll Core Installation Instruction (A) 1” roll core installation (B) 1.5” roll core installation (C) 3” roll core installation EZ-1000P

2-4. Card / Hang tags Installation When installing cord tags, the tag hole must align with the sensor arrow (as indicated in figure), then use the Lab

2-6. Driver Installation 1. Insert product CD to your computer’s CD Drive and find the "Windows Drives" folder. 2. Select the icon of d

6. Select connection port. 7. Enter the printer name and set printer sharing option. 8. A description page of printer settings will be displa

3. Accessory 3-1. Stripper Module Installation 1 Stripper Module 2 Screw (TAP 3*8) x 2pcs 【Note1】 Please power off the printer before installing the

FCC COMPLIANCE STATEMENT FOR AMERICAN USERS This equipment has been tested and found to comply with the limits for a CLASS A digital device, pursuant

5. Plug in the stripper connector onto the switchboard socket. (refer to the right figure) 【Note】 There are 2 sockets on the converting boards (on

10. Follow the direction as shown in figure to feed the liner across the stripper. 11. Close the upper print mechanism and the stripper. 12. Pres

3-2. Cutter Module Installation 1 Cutter Module 2 Screw (TAP 3*8) x 2pcs 21 【Note1】 Please power off the printer before installing the cutter module.

6. Place the left side of the stripper first, and then fit the right side. 7. Flip the cutter module downward to open the cutter. 8. Hold the cut

3-3. Ethernet Module Installation 1 Ethernet Cable 1.8M 2 Bracket 3 Ethernet module 4 Module Connection Wire 5 Bracket Screw*2 6 Secure Screw*

7. Cut the cable tie on the Module Connection Wire. Then Plug the connector into the socket on Ethernet module. 【Note】 Please cut th

3-4. WLAN Module Installation 1 Ethernet Cable 1.8M 2 Secure Screw*1 3 Bracket Screw*2 4 Module Bracket 5 WLAN module 6 Module Connection Wire

7. Cut the cable tie on the Module Connection Wire. Then Plug the connector into the socket on WLAN module. 【Note】 Please cut the

13. Put the Fixture Plate first then the Washer and tighten the Nut to mount Antenna Connection Wire on the printer. 【Note】 It is suggest

3-5. CF Card Adapter Installation 1 CF Card Adapter (Front) 2 CF Card Adapter (Back) 【Note】 Please power off the printer before installing the CF

Safety Instructions Bitte die Sicherheitshinweise sorgfältig lesen und für später aufheben. 1. Die Geräte nicht der Feuchtigkeit aussetzen. 2. Be

3-6. CF Card Instruction EZ-1000Plus series printers can read the CF Card after installed the CF Card Adapter. If the built-in memory is insufficien

4. Printer Setting 4-1. FEED Key After pressing the FEED key, printer will feed the media (according to media type) to the specified stop position. Wh

4-4. Self-Test page The Self-Test page helps user to figure out whether the printer is operating normally. Below are some general descriptions about t

4-5. Error Messages LED Light Ready Status Beep Description Solution Red 4 beeps twice Print head is not firmly closed.Re-open the print head and ma

5. Maintenance and Adjustment 5-1. Thermal Print Head Cleaning Unclear printouts may be caused by dusty print head, ribbon stain or label liner glue.

5-3. Print Line Adjustment To get better printing balance and quality, use print head adjusting gear to adjust the contacting surface between print he

5-5. Troubleshooting Problem Recommended Solution Power on the printer, but the LED does not light up ♦ Check the power connector LED light turns re

Appendix Certifications EZ-1000Plus User’s Manual 36

EZ-1000Plus User’s Manual 37

EZ-1000Plus User’s Manual 38

Safety Instructions Please read the following instructions seriously. 1. Keep the equipment away from humidity. 2. Before you connect the equipme

EZ-1000Plus User’s Manual 39

EZ-1000Plus User’s Manual 40

EZ-1000Plus User’s Manual 41

EZ-1000Plus User’s Manual 42

1. BARCODE PRINTER... 5 1-1. Printer Accessories...

1. Barcode Printer 1-1. Printer Accessories After unpacking, please check the accessories that come with the package, and store appropriately.  Barc

1-D Bar codes: Code 39, Code 93, Code 128 (subset A, B, C), UCC/EAN-128 K-Mart, UCC/EAN-128, UPC A / E (add on 2 & 5), I 2 of 5, I 2 of 5 with Sh

1-3. Communication Interface Parallel Interface Handshake : DSTB connects to the printer, BUSY connects to the host Interface cable : Parallel cab

Internal Interface UART1 wafer Ethernet module N.C 1 1N.C TXD 2 2RXD RXD 3